What Is a Good Borehole Yield in Kenya? Litres per Hour by Use

What to know

  • Borehole yield is how much water a borehole can give steadily, measured in cubic metres per hour (m³/h). One m³/h is 1,000 litres per hour.
  • Under about 0.5 m³/h is a low yield, 0.5 to 2 m³/h suits most homes and small farms, and above 2 m³/h is a good yield for irrigation or business use.
  • The yield you need depends on daily water use and how many hours you pump. Solar pumps get fewer hours, so they need a higher yield for the same water.
  • Only a proper test pump tells you the real yield. A reading taken on drilling day is not enough.

“How much water does it give?” is the first question everyone asks after a borehole is drilled. The answer is the yield, and whether it is good depends entirely on what you need the water for.

A yield that is perfect for a family home can be far too low for two acres of tomatoes. This guide explains what the numbers mean, gives clear ranges by use, and includes a calculator so you can work out the yield your plans need.

What borehole yield means

Yield is the volume of water a borehole can supply in a set time without the water level falling out of control. In Kenya it is usually quoted in cubic metres per hour, written as m³/h.

Converting is easy. One m³/h equals 1,000 litres per hour, so a 2 m³/h borehole can fill a 10,000 litre tank in about five hours of pumping.

The key word is steadily. Almost any borehole can give a big gush for a few minutes, but the safe yield is what it can keep giving hour after hour while the water level settles.

What counts as a good borehole yield in Kenya?

There is no single number that is good for everyone. Use this table as a guide to what each range can usually support.

YieldLitres per hourUsually enough for
Under 0.5 m³/hUnder 500A single home with good storage, a hand pump, a small kitchen garden
0.5 to 2 m³/h500 to 2,000Most homes, a few dairy cows, poultry units, small drip plots
2 to 5 m³/h2,000 to 5,000Larger farms, schools, apartments, a small water vending point
Above 5 m³/hAbove 5,000Several acres of irrigation, estates, water businesses, institutions

So a “good” yield is one that covers your daily water use within the hours you can pump, with some margin left over. The calculator below does that sum for you.

How much yield do you need? Calculator

Enter what the borehole will supply each day. The calculator works out your daily water use and the tested yield to look for.

Daily water use0 litres
Pump rate needed0 m³/h
Tested yield to look for0 m³/h
Fill in your numbers and press Calculate.

Assumptions: 80 litres per dairy cow, 5 per goat or sheep, 0.3 per bird, and 20,000 litres per acre of drip on a hot dry day. Tested yield allows a 25 percent safety margin.

Worked examples

A family home in Kiambu

Six people using about 100 litres each need around 600 litres a day. Pumping for 10 hours, that is only 0.06 m³/h, so even a low yield borehole works well with a tank.

A small dairy farm

Ten dairy cows at about 80 litres each plus a household of six comes to about 1,400 litres a day. A lactating cow drinks more as milk output rises, so plan generously, and see our guide to borehole water for dairy and poultry farms.

Two acres of drip irrigation on solar

On a hot dry day, crops can use about 5 millimetres of water, which is roughly 20,000 litres per acre. Two acres need about 40,000 litres, and with only 6 good solar hours that means about 6.7 m³/h of pumping.

Add a safety margin and you want a tested yield of around 9 m³/h. This is why irrigation plans must be checked against the survey before you buy pipes, and our borehole irrigation guide covers how to plan it.

Steel frame for a solar array that will power a borehole pump
Solar pumps only run in good sunlight, so they need a higher yield to deliver the same daily water.

What affects borehole yield

  • The aquifer. Sandy and fractured volcanic layers often give more water than tight clay or solid rock. Our guide to borehole depth by county shows how ground conditions vary across Kenya.
  • The site. A borehole sited on a good survey anomaly can yield far more than one a short distance away, which is why a geophysical survey comes first.
  • Construction. Screens placed opposite the right water strikes, the correct slot size and a good gravel pack all help water enter easily. See our guide to perforated casing vs borehole screens.
  • Depth. Drilling deeper can reach more water strikes, but only if the survey shows water bearing layers below.
  • Season. Shallow aquifers drop in long dry spells, as explained in borehole yield during drought.

How yield is measured

The reliable way is a test pump. A pump is run at a steady rate, often for 24 hours, while the water level is recorded, then the recovery is measured after the pump stops.

The result gives a safe pumping rate and tells you how deep to set the pump. Read the full process in our borehole test pumping guide.

Plan below the tested figure. A common rule is to run the pump at no more than about 75 percent of the tested yield. That margin protects the borehole in dry seasons and keeps the pump from running dry.

Once you know the yield, you can choose the right pump. Our borehole pump sizing guide shows how to match the pump to both the yield and the height the water must be lifted.

If your yield is low

A low yield does not always mean a failed borehole. Many homes run well on a modest yield by pumping slowly for longer hours into storage.

  1. Add storage. A larger tank or water tower lets the pump work slowly all day and still meet peak demand.
  2. Match the pump. An oversized pump empties the borehole and switches off often, which wears it out.
  3. Check the borehole. If yield has dropped over time, clogged screens or silt may be the cause, and rehabilitation can often restore it.
  4. Cut waste. Drip irrigation and timed watering stretch every litre further.

Not sure what yield your plot can give?

Tell us your location and how you plan to use the water. The Bonvic team will advise on the survey and send a written quote for drilling and test pumping.

WhatsApp 0727 666 444Call 0797 000 555

Frequently asked questions

What is a good borehole yield in Kenya?

It depends on use. Around 0.5 to 2 cubic metres per hour suits most homes and small farms, while irrigation and water businesses usually need more than 2, and often above 5.

How many litres per hour is 1 m³/h?

One cubic metre per hour is 1,000 litres per hour, or 24,000 litres if the pump ran for a full day.

How do I know my borehole yield?

A test pump measures it. The pump runs at a steady rate, often for 24 hours, while the water level is recorded, and the recovery is measured afterwards.

Can borehole yield increase?

Yield can sometimes be improved by cleaning and redeveloping the borehole, deepening it to reach more water strikes, or fixing clogged screens. A new site may be needed if the aquifer itself is poor.

How much water does a dairy cow need per day?

A milking cow commonly needs around 50 to 100 litres a day, and more in hot weather or at high milk output. Planning on about 80 litres per cow is a sensible starting point.

Sources: UN Water for Life, human right to water (50 to 100 litres per person per day for basic needs); UC Davis, water needs of dairy cows; Bonvic drilling and test pumping practice.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top